SS304 Single Braided Flexible Hose: Spec, Sourcing, and PH Delivery

A SS304 single braided flexible hose is built from a corrugated SS304 stainless steel inner tube covered by one layer of braided SS304 wire mesh. The corrugation gives the hose its flexibility so it can absorb movement, misalignment, and thermal expansion in a piping run. The single layer of braid sits over that corrugated core to hold working pressure and resist kinking, without the added stiffness and cost of a second braid layer. This construction is common on water, steam, and general process piping where the line needs to flex at a pump connection, tank nozzle, or expansion joint but does not see constant high amplitude vibration. Buyers in the Philippines often search for this product by a specific brand name they have seen on an existing installation, but the underlying spec, SS304 material, corrugated inner tube, single wire braid, is what actually determines fit, pressure rating, and service life. When you send an RFQ, quote the nominal bore size, working pressure, temperature, and end fitting type (flanged, threaded, or welded nipple) instead of a brand name, so the hose supplied matches the application regardless of which manufacturer originally supplied the installed unit you are replacing.

Single braid and double braid SS304 hose look similar but are rated for different duty. Single braid suits standard commercial plumbing risers, water transfer lines, and steam trap bypass runs where pressure is steady and vibration is limited to occasional movement at the connection point. Double braid adds a second layer of wire mesh over the first, which raises the burst pressure margin and gives better resistance to abrasion and fatigue where the hose sees continuous vibration, such as a direct connection to a running pump discharge or a compressor line. If your application involves constant vibration, pressure cycling, or a safety critical line, double braid is the safer spec even at the extra cost. If the run is a standard water or steam service connection with occasional flexing, single braid is normally enough and costs less. When in doubt, describe the vibration source, duty cycle, and working pressure in your RFQ so the spec can be checked against the application before an order is placed, rather than choosing single or double braid by habit or by matching what was installed previously without confirming it was correctly specified in the first place.

SS304 single braided flexible hose shows up wherever a piping run needs to flex without adding a mechanical expansion joint. Typical points of use include potable water riser connections in commercial and residential buildings, steam trap bypass and condensate return lines, and suction or discharge connectors at a booster or transfer pump where rigid pipe would transmit vibration into the surrounding structure. Hotels, hospitals, food processing facilities, and PEZA or SBMA zone factories all use this hose spec at the same connection points, since the flexibility requirement comes from the piping layout and equipment, not from the industry. When a hose is installed directly at a pump connection, matching it to the pump's duty cycle matters more than matching brand, since a hose rated for occasional flexing will wear faster on a pump that runs continuously than one rated for continuous vibration. JOHOB supplies SS304 single braided hose as part of a wider piping, fittings, and pumping systems catalog, so a facility can source the hose alongside the valves, fittings, or pump it connects to in the same RFQ.

JOHOB Hardware Trading sources SS304 single braided flexible hose from an ISO 9001 certified partner factory and the hose is TUV SUD tested before it reaches the Philippines. As a Philippines based supplier, JOHOB handles quality checks on incoming stock, provides a local warranty, and manages after sales support directly, so a buyer does not need to coordinate a claim across time zones with an overseas manufacturer. This matters for facilities teams and procurement officers who need a hose replaced quickly rather than an equipment problem that stalls while a claim moves through an overseas contact. Every unit supplied is built to the same SS304 material and single wire braid construction regardless of which specific end fittings or lengths are ordered, and JOHOB can confirm the material certificate and test documentation for a given order on request. For buyers who are standardizing a facility on one hose spec after replacing an installation that used a specific branded product, this sourcing and warranty setup is the practical difference between a one off purchase and a supplier who can restock the same spec reliably as more lines need replacement across a site.

Pricing for SS304 single braided flexible hose is quote based since size, pressure rating, end fitting, and length all change the final cost, so JOHOB does not publish a fixed price list for this product. Send bore size, working pressure, temperature, end fitting type, and quantity, and JOHOB responds to the RFQ within 1 business day. Standard lead time is 21 to 35 days ex-stock for common sizes, and 45 to 90 days for made-to-order lengths, fittings, or spec combinations that are not held in standard stock. Pricing to VAT-registered buyers includes 12% VAT. Buyers registered with PEZA or SBMA, and exporters, qualify for zero-VAT pricing on the same order. Facilities standardizing across multiple sites should request a single quote covering all sizes and quantities needed, since consolidating an order into one RFQ can simplify both lead time planning and VAT documentation, compared to placing several smaller orders across different months as each individual line item fails and needs separate replacement.

JOHOB delivers SS304 single braided flexible hose nationwide across the Philippines, covering NCR, the rest of Luzon, Visayas, and Mindanao. JOHOB also delivers into PEZA and SBMA economic zones and the Clark freeport area, which matters for exporters and locator companies that need equipment delivered inside a zone under zero-VAT terms rather than routed through a third party. Facilities in provincial areas outside Metro Manila are quoted the same way as NCR facilities, RFQ response within 1 business day, with delivery lead time added on top of the standard 21 to 35 day ex-stock or 45 to 90 day made-to-order production window depending on distance and the freight arrangement selected for that order. Buyers managing multiple facilities across different regions can request one consolidated quote that lists delivery lead time by site, so procurement and site engineering teams both work from the same figures when scheduling installation or a shutdown window for the hose replacement.